OTN SystemsDCI Platforms

Optical Channel Monitoring Card for DCI Chassis

A DWDM network carries dozens or hundreds of wavelengths on the same fibre, and each one needs to stay at its assigned frequency and power level for the system to work correctly. The Optical Channel Monitoring Card is the instrument that checks this: it measures the exact centre wavelength and optical power of every individual channel inside a combined DWDM signal, without interrupting traffic. Think of it as a spectrum analyzer built into the chassis - instead of unplugging a fibre and connecting an external test instrument, the card receives the light tapped from up to 8 different points in the network (typically the MON ports of amplifier cards) and reports back precise per-channel readings to the management system.

Optical Channel Monitoring Card for DCI Chassis

Wavelengths can drift off-centre or lose power as equipment ages or conditions change, and a channel that drifts too far can start interfering with its neighbours or falling below the receiver’s sensitivity threshold - long before the connection actually fails outright. By continuously watching centre wavelength and power on every monitored port, this card lets the network management system catch that kind of slow degradation early, well before it becomes a service-affecting fault, and gives technicians the hard numbers they need to diagnose a problem instead of guessing.

Per-channel wavelength & power

Measures the centre wavelength and optical power of every channel inside a combined DWDM signal.

8 test ports, one analyzer

An internal 1×8 optical switch selects one of 8 test points at a time and feeds it to a single shared analyzer engine - no need for 8 separate instruments.

High accuracy

±0.1nm centre wavelength accuracy, 0.02nm resolution; ±0.8dB power relative accuracy, 0.1dB resolution.

Fast scanning

Full scan in ≤1s, so monitoring stays close to real time even while cycling through all 8 ports.

50/100GHz and Flexible Grid

Works across fixed 50GHz/100GHz DWDM grids as well as Flexible Grid deployments.

Non-intrusive

Each test port is fed from a monitoring tap (MON port) elsewhere in the system, so only a small fraction of the optical signal is measured - live traffic is undisturbed.

OCMMON1(IN)MON2(IN)MON3(IN)MON4(IN)MON5(IN)MON6(IN)MON7(IN)MON8(IN)1:8 Switch

The internal 1×8 optical switch selects one of the 8 test ports (MON1–MON8) at a time and routes it to the shared OCM analyzer.

Front panel of the Optical Channel Monitoring Card for DCI Chassis
CARD FOR DCI CHASSIS1 SLOT
FunctionMeasurement of centre wavelength and optical power for each channel in a combined DWDM signal
Slots Occupied1
Test Ports8 input-only test interfaces, selected one at a time by an internal 1×8 optical switch
Working Wavelength Range1528.57–1567.34nm (191.27–196.15THz)
Channel Spacing50/100GHz, Flexible Grid support
Centre Wavelength Detection Accuracy±0.1nm
Centre Wavelength Resolution0.02nm
Channel Power Monitoring Range-40 to -10dBm
Absolute Power Accuracy≤1dB
Power Relative Accuracy±0.8dB
Optical Power Resolution0.1dB
Return Loss≥40dB
Scan Time≤1s
Scan Cycles>109
NameOptical Channel Monitoring Card for DCI Chassis
DescriptionOptical channel monitoring card, 1 slot. Measures centre wavelength and optical power of each channel in a combined DWDM signal across 8 input-only test ports selected by an internal 1x8 optical switch. 1528.57-1567.34nm, 50/100GHz + Flexible Grid; wavelength accuracy +/-0.1nm; power range -40 to -10dBm, +/-0.8dB relative accuracy; scan time ≤1s.
Part NumberDCI-OCM-1S
© Nexgen A/S, OTN DCI platformDatasheet Version 1.0.0 (Released) · 17 Nov 2026nexgen.eu · customer.service@nexgen.eu